Schneider Electric (EM3502,EM3550) логгер. Карта регистров MODBUS.


Данные ниже соответствуют только программе Advanced Serial Data Logger или Advanced TCP/IP Data Logger и могут быть не применимы для других программных продуктов.

Смещение MODBUSОписаниеЕд. изм.Тип данных
2Сумма instantaneous real мощность (3 фаза сумма)kWword
3Сумма instantaneous реактивная мощность (3 фаза сумма)kVARword
4Сумма instantaneous кажущаяся мощность (3 фаза сумма)kVAword
5Сумма коэффициент преобразования мощности (сумма kw / сумма kva)Ratioword
6Напряжение, L l, average of 3 фазаsVoltword
7Напряжение, L n, average of 3 фазаsVoltword
8Ток, average of 3 фазаsAmpword
9Real мощность, фаза AkWword
10Real мощность, фаза BkWword
11Real мощность, фаза CkWword
12Коэффициент преобразования мощности, фаза ARatioword
13Коэффициент преобразования мощности, фаза BRatioword
14Коэффициент преобразования мощности, фаза CRatioword
15Напряжение, фаза A BVoltword
16Напряжение, фаза B CVoltword
17Напряжение, фаза A CVoltword
18Напряжение, фаза A NVoltword
19Напряжение, фаза B NVoltword
20Напряжение, фаза C NVoltword
21Ток, instantaneous, фаза AAmpword
22Ток, instantaneous, фаза BAmpword
23Ток, instantaneous, фаза CAmpword
25Частота (derived from фаза a)Hzword
26Кажущаяся energy consumption (msr)KVAhdword
28Реактивная energy consumption (msr)KVARhdword
30Кажущаяся мощность, фаза AkVAword
31Кажущаяся мощность, фаза BkVAword
32Кажущаяся мощность, фаза CkVAword
33Реактивная мощность, фаза AkVARword
34Реактивная мощность, фаза BkVARword
35Реактивная мощность, фаза CkVARword
36Сумма real мощность present demandkWword
37Сумма реактивная мощность present demandkVARword
38Сумма кажущаяся мощность present demandkVAword
39Сумма real мощность max. demandkWword
40Сумма реактивная мощность max. demandkVARword
41Сумма кажущаяся мощность max. demandkVAword
42Pulse counter 1 (real energy) dword
44Pulse counter 2 (реактивная energy) dword
46Real energy consumption фаза AkWhdword
48Real energy consumption фаза BkWhdword
50Real energy consumption фаза CkWhdword
129Single фаза: A + N word
130Ct ratio primaryAmpsword
131Ct ratio secondary interface (1 or 1/3 v, may not be user configurable) word
132Pt ratio: the meter scales this value by 100 (i.e. entering 200 yields a potential transformer ratio of 2:1). the default is 100 (1.00:1), which is with no pt attached. set this value before setting the system напряжение (below) word
133System напряжение: this напряжение is line to line, except for system type 10 which is line to neutral. the meter uses this value to calculate the full scale мощность for the analog выходs and pulse configuration (below), and as full scale for фаза loss (register 142). the meter will refuse напряжениеs that are outside the range of 82 660 вольтаж when divided by the pt ratio (above) word
134Theoretical maximum system мощность: this read only value is the theoretical maximum мощность the meter can expect to see on a service. this value is 100% of scale on the analog выход (0 5 vdc or 4 20 ma), if equipped. the meter recalculates this value if the user changes the ct size, system type, or system напряжение. this integer value has the same scale as other integer мощность registers (see register 140 for мощность scaling)kWword
136Display units: 0 = iec (u, v, p, q, s), 1 = ieee (default: vll, vln, w, var, va) word
137Scale factors note: these registers contain a signed integer that scales the corresponding integer registers. floating point registers are not scaled. scaling is recalculated when the meter configuration is changed smallint
Есть еще ряд значений MODBUS для этого устройства. Их можно посмотреть в программе.

Замечание: Продукты и компании, указанные здесь используются только для обозначение и идентификации и могут быть торговыми и/или зарегистрированными марками соответствующих компаний.