ESI v3 (csv). Параметры соединения и формат данных SMDR/CDR


Данные ниже соответствуют только программе Advanced PBX Data Logger и могут быть не применимы для других программных продуктов.

SMDR formats

Supported models: ESI-1000, ESI-600, ESI-200, ESI-100, ESI-50

Advanced PBX Data Logger supports: CSV and Extended SMDR formats

Capturing SMDR data over Ethernet

The NSP1 can be used to output SMDR data over an IP network. The TCP can be xx003 (default value is 59003). For more information about PBX settings, see NSP Installation Made Simple (ESI # 0450-0669).

Настройка логгера в режиме TCP клиента

Наша программа должна работать в режиме TCP клиента. Это означает, что логгер сам инициирует подключение с АТС, которая работает в режиме сервера. Добавьте один или несколько IP адресов вашей АТС ((none)). Номер порта должен соответствовать номеру порта, установленному в настройках АТС или производителем (в этом примере - 59003).

1. Добавьте новую конфигурацию с источником данных типа TCP, если не сделали это ранее.

Тип интерфейса TCP/IP

2. Настройте параметры TCP подключения как показано ниже.

Режим TCP клиента - ESI

192.168.1.220

59003

192.168.1.220:59003

Capturing SMDR data through RS-232 port

Use an RS-232C cable to connect a PC's serial port to the system's Maintenance/SMDR port. If necessary, consult the Hardware Installation Manual. SMDR data will be stored temporarily if a laptop is connected for programming (5-15 minutes). The buffered SMDR data will resume output to the serial port.

Entering programming mode

You may program from any ESI desktop phone in the system:

1. Press PROG/HELP at any station. The normal station programming menu prompts will begin to play.
2. Press HOLD. The "enter password" prompt will play.
3. Enter the Installer password (default is 789). Then, to confirm the password, either press # or wait two seconds. You are now in programming mode. The extension will be automatically placed in DND, and its display will show:
INSTALLER
CMD:
4. The system will play the system programming menu. Follow it to program as you wish.
5. When finished, hang up.

Function 18: Maintenance/SMDR serial port

Real-time SMDR call records are continuously output to the SMDR port.

1. Select the output device by pressing the scroll keys (SERIAL or ETHERNET (if connecting to a LAN through an NSP board)).
2. The system will then prompt you for the serial port baud rate. You can change this rate by pressing the scroll keys.
3. Select the SMDR format, STANDARD, EXTENDED, or CSV, by pressing the scroll keys.

If necessary, consult the ESI Communications Servers: Programming Manual

Выбор правильного модуля-парсера для ESI v3 (csv)

Выбор парсера для (none)

ESI v3 (csv)

ESI v3 (csv)

Данные, извлекаемые PBX Data Logger

ОписаниеТип данныхИмя колонки
Тип звонкаstringCALL_TYPE
НаправлениеstringDIRECTION
Время звонкаdatetimeCALL_TIME
Длительность звонкаdatetimeCALL_DURATION
Длительность звонка (с)integerCALL_DURATION_S
РасширениеstringEXT
ТелефонstringDIALED_PHONE
Caller ID namestringCALLER_PHONE
Esi-Link home location numberstringFLAG1
Esi-Link remote location numberstringFLAG2
номер линииstringTRUNK

Интересуют отчеты об использовании АТС?

Мы предлагаем утилиту PBX Reports с разнообразными ручными и автоматизированными отчетами, с возможностью вывода на печать, в файлы Excel или PDF, или отправкой по электронной почте, встроенный веб-сервер, и другие возможности. Смотрите тут

Нужна история звонков в базе данных?

Это стандартная функция нашего логгер, который получает и экспортирует данные SMDR или CDR в реальном времени в вашу базу данных. Проследуйте по ссылке

Замечание: Продукты и компании, указанные здесь используются только для обозначение и идентификации и могут быть торговыми и/или зарегистрированными марками соответствующих компаний.